Peak Oil is You

Donate Bitcoins ;-) or Paypal :-)

Page added on February 24, 2013

Bookmark and Share

Fusion Experiment JT60-SA Assembly Started in Japan

Fusion Experiment JT60-SA Assembly Started in Japan thumbnail

In another small step on the long path to bring the sun’s fusion fire down to Earth, the construction of the large auxiliary Tokamak JT-60SA, associated to the world’s largest fusion experiment ITER, began in Japan this year. The project is one of several large fusion science facilities built together by Japan and the European Union and will model proposals for optimizing plasma operation and investigate advanced plasma modes that could be tested on ITER or used later on the first fusion power-plant prototype DEMO. Plasma is the fifth state of matter and essentially super-heated and fully ionized gas which in tokamaks is confined in a torus-shaped (or donut like) vacuum room by very strong magnetic fields–one of the most difficult engineering tasks ever attempted.


JT60-SA Tokamak assembly fusion energy

(Photo : JT60-SA)
One of the lower structure sectors of the cryostat base as it is assembled in the torus hall on 28 January in the presence of the media.

On 28 January, tokamak assembly for JT-60SA began with the cryostat base, the first major component to be delivered by Europe. This marks a crucial step forward for the project, which is part of the Broader Approach Agreement (for fusion energy) signed between Japan and Euratom, and implemented by Japan Atomic Energy Agency (JAEA) and Europe’s Fusion for Energy (F4E) agency.


The cryostat base, which supports the weight of the entire tokamak, has a diameter of 12 metres, a height of 3 metres and weighs 250 tonnes. It consists of a double ring in three sectors, a lower structure in three sectors, and an inner cylinder and is assembled using connecting bolts. The manufacturing of the cryostat base was carried out in Aviles, Spain, by IDESA; final machining and pre-assembly was done by ASTURFEITO under the supervision of CIEMAT.

Anticipation had started to build already in November 2012 with the final pre-assembly of the cryostat base at the manufacturing facility. An accurate dimensional tolerance check was performed with a 3D portable laser tracker, and results proved to be satisfactory with low error under the limits.

By 8 November, the manufacture was completed and all parts of the cryostat base were packed for transport. Due to their large size (maximum width 6.5 m), the pieces were difficult to transport, especially by road, but fortunately the factories where the cryostat base was fabricated and machined were close to one another as well as to the port.

The cryostat base was collected from the factory on 12 November and transported to the port. After loading the cryostat base on board the IYO, the ship set sail on 22 November and took on further cargo at other European ports before heading across the Atlantic and Pacific oceans via the Panama Canal. After the 18,000-km-long sea voyage, the cryostat base finally arrived at Hitachi port in Japan on 16 January 2013.

The transport from the port to the Naka Fusion Institute was conducted by JAEA in seven stages during the week starting 19 January. Transport was carried out before dawn on closed roads. All seven pieces of the cryostat base were delivered to the assembly hall at the Naka Fusion Institute by 26 January.

Tokamak assembly began two days later. The start was open to the press and reporters from ten media organizations were able to witness the first assembly work. This event was widely reported to the public through newspapers, web, and TV, including the national news.

This timely start to the assembly of the JT-60SA Tokamak is the beginning of a six-year assembly and commissioning period which will enable the first plasma to be achieved in March 2019, ready for this project’s role to support and complement ITER.

science world report

One Comment on "Fusion Experiment JT60-SA Assembly Started in Japan"

  1. DC on Sun, 24th Feb 2013 7:56 pm 

    Cutting edge science and engineering is all good and ok, but, shouldn’t Japan clean up its current nuclear FISSION mess before throwing good money after bad trying to make an even more costly FUSION mess?

    Jus wunnerin

Leave a Reply

Your email address will not be published. Required fields are marked *